The short answer
Chimney waterproofing means finding and repairing the places where water gets into your chimney, then coating the exposed brick with a breathable, vapor-permeable water repellent. If you see white staining on the brick, water or rust in the firebox, or flaking brick, have the chimney inspected before the damage spreads.
Water does more damage to a masonry chimney than fire does. Brick and mortar are porous, and every rainstorm, snowmelt and freeze-thaw cycle pushes moisture deeper into them. Over time that moisture breaks down mortar joints, cracks the crown, rusts the damper and can stain the ceilings and walls next to the chimney. Many homes in Brooklyn and nearby neighborhoods have older brick chimneys standing exposed above the roofline, so these problems are common. RoyalFlue Chimney Services handles waterproofing in a set order. We inspect the chimney, repair the places where water is getting in, and then apply a breathable water repellent made for masonry. The brick sheds rain but can still let trapped moisture escape.
Signs You Need Chimney Waterproofing
Moisture damage builds slowly, and most homeowners notice the symptoms long before they find the cause. Some signs show up outside on the brick. Others show up inside, in or around the fireplace. If you see any of the following, water is probably moving through the chimney.
- White, chalky staining on the outside brick, which shows that water is passing through the masonry and leaving minerals behind
- Water, drips or rust stains in the firebox or on the damper after it rains
- Flakes of brick, mortar or flue tile collecting in the firebox
- A stronger smoke or creosote smell on humid or rainy days, because damp deposits in the flue give off more odor
- Brick faces that crack, pop off or crumble on the outside of the chimney
- Water stains, bubbling or peeling paint on the ceiling or wall next to the chimney

What Is Included
A water repellent only works on masonry that is sound. If the crown is cracked or the flashing is loose, coating the brick will not keep water out. Every waterproofing job therefore starts with finding and fixing the entry points. Before any repair beyond the basic scope, we tell you what we found and get your approval.
- Inspection of the chimney exterior, crown, flashing, cap and flue
- Camera scan of the flue when there are signs of water damage inside the chimney
- Cleaning the brick so the repellent can soak in evenly
- Sealing hairline cracks in the crown, or recommending a rebuild if the crown has failed
- Checking the flashing where the chimney meets the roof and resealing it as needed
- Repointing small areas of failed mortar before the coating goes on
- Installing or replacing a chimney cap to keep rain and animals out of the flue
- Applying a vapor-permeable masonry water repellent to the exposed chimney
- Photos and written notes on the conditions we found and the work we did
How Our Crew Works Inside Your Home and on the Roof
Most of the waterproofing work happens on the roof, but we usually need to reach the fireplace as well. Indoors, our certified technicians lay drop cloths from the door to the hearth and seal the fireplace opening. They use HEPA vacuums to capture soot and dust. If the flue needs sweeping before the inspection, they use rotary brushes, and they run a camera up the flue to look for cracked tiles, gaps in the mortar joints and water staining you cannot see from below.
On the roof, the crew protects the roofing around the chimney before cleaning or treating anything. They make repairs first and let new mortar or crown material cure before applying the repellent. The repellent goes on in dry weather, which affects scheduling. Before we leave, the crew cleans up the work area inside and out.
Time for your annual chimney check?
The Standard We Follow
The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. Chimney professionals use three inspection levels. Level 1 applies when nothing about the system has changed. Level 2 applies when the system changes, for example with a new appliance or a switch of fuel, or when the home is sold. Level 3 applies when a hidden hazard can only be reached by opening part of the chimney or the building. Most waterproofing visits start with a Level 1 or Level 2 inspection.
Moisture problems are especially common after an oil-to-gas boiler conversion. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue. If we see signs of that kind of damage, we explain the liner options separately from the waterproofing.
What Affects the Price
Every chimney is different, so we quote after we see it. The main factors are listed below.
- Chimney height and how easy the roof is to reach and work on
- Fuel type and what the flue has been venting, since gas and oil cause different kinds of wear
- Flue size and condition, including cracked tiles or a missing liner
- How much soot or creosote buildup has to be removed before inspection
- Whether a camera inspection is needed
- Whether the crown, flashing, cap or mortar needs repair before the repellent can go on
How a Visit Works
When you contact us, we ask what you have noticed and where. On the day of the visit, the crew protects your floors, inspects the chimney from the inside and from the roof, and walks you through what they found, with photos. You get a clear scope of work before any repairs begin. Simple jobs can sometimes be finished in one visit. Jobs that need crown or masonry repair take a second trip so the materials can cure before the repellent is applied.
Timing matters. Waterproofing needs dry weather, and New York City's heat season runs from October 1 through May 31. Many owners prefer to have the chimney sealed and repaired before the heating system is working hard.

