The short answer
A chimney cap covers the top of the flue, and a chase cover seals the top of a factory-built chimney's enclosure. Both keep water, animals and debris out. If you see water in the firebox, hear animals, or notice rust or white staining on the chimney, have the chimney top checked and the cap or cover replaced.
A chimney cap and a chase cover are small parts with an important job: they keep rain, snow, animals and debris out of your flue. On Brooklyn row houses, brownstones and frame homes, the top of the chimney takes the weather all year. A missing cap or a rusted chase cover usually shows up first as a stain on the ceiling, a puddle in the fireplace or a bird in the firebox. RoyalFlue Chimney Services measures, fits and installs chimney caps and chase covers for homes in Brooklyn and nearby neighborhoods. While we're on the roof, we also inspect the top of the flue.
Signs you need a new chimney cap or chase cover
Most cap and chase cover problems are noticed from inside the house, not from the roof. These are the signs homeowners tell us about most often:
If you find water or hear an animal, stop using the fireplace until the flue has been checked.
- Water dripping into the firebox or pooling on the smoke shelf after rain
- Animal noises in the chimney, such as scratching, chirping or nesting sounds, often in spring
- Leaves, twigs, nesting material or brick flakes landing in the firebox
- White staining on the exterior brick, a sign that water is moving through the masonry
- Rust streaks running down the siding below a metal chase on a factory-built chimney
- A damp, musty or creosote smell in the room, often worse in humid weather when moisture mixes with deposits in the flue
- Poor draft, or smoke rolling into the room on windy days

What's included
Every cap and chase cover job includes the same core steps. That applies whether we're replacing a dented cap on a masonry chimney or fitting a new cover on a factory-built one.
- Visual inspection of the accessible flue, crown and chimney top
- Measuring each flue tile or chase top for an exact fit instead of guessing at a stock size
- Removing the old, damaged or rusted cap or chase cover
- Clearing nests, leaves and loose debris from the top of the flue
- Installing a cap with mesh screening sized to keep animals out without choking the draft
- Fitting a chase cover with a drip edge and a sloped or cross-broken top so water runs off instead of pooling
- Fastening and sealing the cap or cover so it stays put in high wind
- Checking the crown for cracks and noting any masonry repairs needed
- Photos of the chimney top and a written summary of what we found and what we did
How our crew works inside your home and on the roof
Inside, we start by laying drop cloths from the door to the fireplace and covering the hearth. If nesting material or debris needs to come out of the flue, we keep a HEPA vacuum running at the firebox so dust and soot stay contained. We use rotary brushes to loosen material stuck to the flue walls. If the flue can't be seen clearly from either end, we run a camera down it to check the liner for damage hidden behind the debris.
On the roof, the crew sets up safe access first, using ladders, roof brackets or harness anchors as the roof requires. Brooklyn homes range from flat roofs reached through a bulkhead hatch to steep pitched roofs, and we plan for each one. We measure, remove the old hardware, clean the top of the crown, and set the new cap or cover. Before we leave, we confirm the flue is open and drawing and the cap is secure. We also pick up any debris on the roof and around the house.
Time for your annual chimney check?
The standard we follow
Our work follows NFPA 211, the national standard for chimneys, fireplaces and vents. It calls for these systems to be inspected once a year. Chimney professionals use three inspection levels. Level 1 is for when nothing about the system has changed. Level 2 is for when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Level 3 is for when a hidden hazard can only be reached by opening part of the chimney or building.
A cap or chase cover installation usually goes with a Level 1 inspection. If your building is converting its boiler from oil to gas, the chimney has to be evaluated as part of that work in New York City. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue. In that case, we fit a cap sized to match the new liner.
What affects the price
We price each job after seeing the chimney, because no two chimney tops are the same. The main factors are:
We explain your options and the cost before any work begins.
- Chimney height and roof access, including roof pitch and whether we reach it through a hatch
- The fuel the flue serves (wood, gas or oil), which affects cap style and materials
- Flue size, the number of flues, and the condition of the flue tiles and crown
- How much nesting material, debris or creosote buildup has to be removed
- Whether a standard cap fits or a custom cap or chase cover has to be made
- Whether a camera inspection or repairs, such as crown work, are needed
How a visit works
When you contact us, we ask a few questions about your chimney, the fuel it serves and what you've noticed. We schedule an arrival window and come with the equipment for both the inside work and the roof.
On site, a certified technician inspects, measures and walks you through what we found. Standard caps can often be installed in the same visit. Custom chase covers and multi-flue caps are measured first and installed on a return trip. At the end, you get photos and a written summary. New York City's heat season runs from October 1 through May 31, so late summer and early fall are a good time to book. That way the chimney is ready when the heat comes on.

